Photoshop can add sunlight to images by doing the following:

1, open the image and create a new layer.

2, use the pen tool to draw a straight line in the direction of the sun on the new layer. This will serve as the path of sunlight.

3, use the pen tool to adjust the sun path to make it look more natural.

4, use curve or color tool to adjust the overall tone and control of the image.

5. Use the added layer mould to hide the unwanted parts and fine adjust the image until satisfied.

Ps how to add the image to sunlight

0

Add sunlight to the image in the Ps, you can use the following method by extracting high light and applying diameter to the blurred and linear light mixing mode to simulate the sun effect:

Step One: Copy the graphic layer After opening the image, press Ctrl+J to copy the background graphic layer to avoid direct modification of the original image.

0 Step Two: Modulate the high light area

1 Press

2 Ctrl+Alt+2PH 13 Fast
Select the high-light section of the image (applicable to RGB mode), the high-light area will display the status of the ants line selection area.

Step Three: Copy the high-light graph layer Keep the selection area activated, press Ctrl+J to copy the high-light area to a new layer (layer 2), this time the graph layer panel will generate a transparent graph layer that contains only high light.

Step Four: Apply the path to the blur selected layer 2, click the menu bar

0 filter
> blurred > diameter blurred, in the pop-up window:

blurred method select scale, simulate the sunlight radiation effect;

number

0 adjusted to

1 30-50

2 (the higher the number the more blurred);

3

4

5 quality

6 set to

7 best<
/strong>;

Draw the blurred center point to the light source direction (such as the upper left corner of the picture), click to confirm.

Step Five: Change the blended mode to linear light In the diagram layer, change the blended pattern of layer 2 from normal to linear light, so that high light and blurred effects merge, enhancing the perception and contrast of sunlight.

0

1

2 Step Six: Combine the diagram layer and outputg> Right-click layer 2, select to combine the visible layer, combine all the modifications into a single layer and add the sunlight effect.

Note::

is recommended to back up the original map before the operation, to avoid misconduct leading to data loss. The number of blurred and central point position 0 needs to be adjusted according to the direction of the image's light source, simulate the real sunlight angle. The blended mode is changed to After the linear light, if the effect is too strong, you can reduce the opacity of layer 2 (recommended 60% to 80%) to balance the natural degree.

Ps How to add sunlight to the photo?

Add the sun and sunlight to the picture in the ps, you can follow the following steps:

open the ps and fill the front view: open the ps software, click on the "Fill" in the editing, then click on the content to select the "front view", prepare for subsequent operation.

0

1
Choose the lens faint: On the page after filling the front view, right-click the mouse and select the "lens faint" in the rendering. The lens faint effect can simulate the shape of the sun faint, is the key step to add the sun effect.

adjust the parameters and set the layer mixed mode: select 50 - 300mm fainting in the pop-up page, this range can simulate the sun fainting effect of different distances and sizes. At the same time, adjust the brightness to make the fainting effect more natural and obvious. After clicking the "Determine" option, adjust the layer
The filter mode can make the added sunlight dimming effect better fuse with the prototype, showing realistic sun and sunlight effects.

In Photoshop to add the sunlight effect, can be copied by the diagram layer, application diameter to blur, adjust the mixed mode with sharpening, reduce opacity implementation. The specific operation is as follows:

import and copy the graphic layer open Photoshop, import the need to add sunlight effect.
Click on the diagram layer, hold on the CTRL+J copy layer, retain the original image for subsequent adjustment.

Apply the line to the vague Click on the filter in the toolbar above, select vague → 0 to the vague 1 . Set the 2 number 3 to the maximum value, select the vague method g> scale, the quality choice is best. In the central blurry panel, drag the direction slider to the right position (analogue sunlight dispersion direction), click to determine.

adjust the blended mode with sharpened back to the graphic layer panel, change the blended mode to lightweight0 (enhanced light permeability). click 1 filter2 ng> sharpened → USM sharpened, the number is adjusted to the maximum, the radius is set to 2 pixels or so, click to determine0 .
g> (recommended range: 30-70%), make sunlight more natural.

Note:

should be adjusted according to the position of the light source, analyzing the actual light angle.USM sharpened radius

0 values should not be too large, otherwise will lead to marginalized hardness. The final effect can be achieved by

1 opacity

2 and
layered mounting further optimized, highlighting the focus area.